thread chaser set?

[gregburb]

Can anyone recommend a thread chaser set. I want to clean up the threads before putting heads back on.

[vanis13]

FWIW, I've heard that sometimes taps and chasers enlarge the existing holes too much and a good solution for just cleaning the threads is the old bolt (or one same size) with cut a vertical/top-to-bottom slot or two in it with a dremmel. That way you are nor removing any new material.
_________________
83.5 Westy with Subaru 2.5, 4 spd manual, center seat, COLD A/C on 134a!, Winter camp heated with an Espar B4 gasoline furnace

www.SuperVanagon.com - some stuff I make

[4Gears4Tires]

Using an angle grinder to cut a sharp groove into an existing bolt is a great way to chase threads. I've done it before, it works well.

That said, I have a Craftsman thread cleanup kit and they don't enlarge the holes any. They can remove coatings though, and then that sometimes makes a looser fit.

I have a Harbor Freight thread tap kit and that definitely cuts things looser.
_________________
'87 Syncro Ferric Oxyhydroxide Superleggera Edition
'85 Westy Sciuridae Domus Edition

[vanagonjr]

A thread-rolling tap, vs. the more common thread-cutting tap is, in my humble opinion, a better way to “chase” threads.

I tend to use high-quality thread-rolling screws to chase threads. because of my access to such.
_________________
John - 86 Wolfsburg Westfalia "Weekender"
Flint reversed 1.8T W/Passat 5-Speed
LiMBO (late model bus club) www.limbobus.org
LiMBO is on Facebook too! https://www.facebook.com/groups/
FAQ thread: http://www.thesamba.com/vw/forum/viewtopic.php?t=525798

[Mateo83]

I got an easy out set and tap with proper bits at my local fastenal.

[jimf909]

The M12x1.25 nut on the anti-sway bar end link took a leave and the threads on the end link got buggered. I don't have an M12x1.25 die and filing w/ a triangle file isn't delivering an effective result.

Is this end link a candidate for repair or replacement? If repair, what is recommended: thread chaser, thread cutter, file?

Thanks.
_________________
- Jim

[djkeev]

Get a thread repair file, it will change your life!

https://www.amazon.com/General-Tools-177-8-Metric-Thread/dp/B0017R1DOM?th=1

Dave
_________________
Stop Dead Photo Links how to post photos

Ghia
http://www.thesamba.com/vw/forum/viewtopic.php?t=392473

Vanagon
http://www.thesamba.com/vw/forum/viewtopic.php?p=6315537#6315537

Beetle
https://www.thesamba.com/vw/forum/viewtopic.php?t=482968&highlight=74+super+vert

[Abscate]

[jimf909]

Thanks for the tips. I'll attempt a repair and report back.
_________________
- Jim

[?Waldo?]

Rather than using a file or thread cutting die, I would recommend getting a thread forming die or a thread repairing die, either of which will work to push the displaced metal back where it belongs rather than just removing it. The result would be a stronger thread.

[lcolon]

It looks like it is currently out of stock, but this is a great thread chaser set that should cover most of your near term metric needs:

https://www.mcmaster.com/25325A14/

It is a USA made JAWCO 1853 chaser set. Maybe you can find it elsewhere…. Worth a look
_________________
1984 Vanagon Westfalia - Vanna
1971 VW Beetle

[Crankey]

Since the threads are worn away, after chasing they won't be very deep in the shaft...ya know like drilling an oversized hole to make tapping easier, it also makes shallow threads that don't have the same grip or clamping/pulling force.
I mean after chasing those out, the nut will still be loose, and if you try and torque on it you might just scrub the nuts threads past the shaft threads, stripping the remaining thread off the shaft.
It might feel ok and tight-ish after chasing but stress of driving movement could have it fail when your someplace where all you can see is trees and the night sky for miles.

I'd replace it.

[jimf909]

Thanks, folks. I'll try salvaging it with a thread repair die and will be ready to replace it if that isn't adequate (I've pinged Christopher at T3 to see if he has a replacement but I believe he's using different parts for the HD end links nowadays).
_________________
- Jim

[jimf909]

Follow-up: repairing threads on the T3 Technique HD endlink

I bought this cheapo thread repair set on amazon that included both a file and a chaser die (one hardware store in 35 miles and it doesn't stock such tools)
https://www.amazon.com/dp/B07VYGK6GN?ref=ppx_yo2ov_dt_b_product_details&th=1

- First, it became clear that there was no way the die could have been used to start the repair because the threads were too damaged and the chaser couldn't be turned with reasonable force.
- The thread repair file (it is a life changer!) did great work returning the threads to some semblance of their former selves but they still needed work in order to function.
- I could then use the chaser to finish the work and reinstall the end link.
- It took about an hour to repair the thread.

Before (after attempting a fix for about 20 minutes with a triangular file, the first four threads looked as bad as the rest)

After

Not having a vice in this shop required some creativity to hold the threads while using a breaker bar to turn the chaser