| Author |
Message |
Cainepolo12
Samba Member
Joined: December 20, 2005
Posts: 27
Location: Nashville, TN
|
 Posted: Mon Dec 29, 2014 7:18 am Post subject: Where can I find IDF parts? help |
 |
|
| I have a set of Italian 40 IDFs, all of the jets and venturis are new, and they have new gaskets. However, I am missing some of the parts that attach the carbs to the linkage. I have checked places like Appletree, but is there anywhere that I can buy some of these miscellaneous parts? Unfortunately, the nearest show is three hours away and only twice a year. Any help is greatly appreciated. |
|
| Back to top |
|
 |
Dale M.
Samba Member
Joined: April 12, 2006
Posts: 20772
Location: Just a tiny bit west of Yosemite Valley
|
| Posted: Mon Dec 29, 2014 8:45 am Post subject: |
|
|
Maybe here.... Mike is Left Coast Weber dealer and can generally solve any Weber needs... IF you do not see parts you need on webpage, call and ask about what you need... He (or one of his staff) has never failed to solve any carb problems for me...
http://www.piercemanifolds.com/category_s/32.htm
IF you are stuck with throttle arm problem for left hand side "dual" setup, look here...
http://www.cbperformance.com/ProductDetails.asp?ProductCode=6455
CB P also has major linkage parts (look in carbs/linkage section) ...
Or for this kit...
http://vwparts.aircooled.net/Weber-IDF-Linkage-Hardware-Repair-Kit-99004-913-p/99004.913.htm
Dale
_________________
“Fear The Government That Wants To Take Your Guns"
"Kellison Sand Piper Roadster" For Street & Show.
"Joe Pody Sandrover" Buggy with 2180 for Autocross (Sold)
============================================================
All suggestions and advice are purely my own opinion. You are free to ignore them if you wish ... |
|
| Back to top |
|
|
Cainepolo12
Samba Member
Joined: December 20, 2005
Posts: 27
Location: Nashville, TN
|
| Posted: Mon Dec 29, 2014 5:59 pm Post subject: |
|
|
| Thanks Dale- I am going to give him a shout tomorrow. These are some pretty obscure parts so hopefully he is my man. |
|
| Back to top |
|
|
Dale M.
Samba Member
Joined: April 12, 2006
Posts: 20772
Location: Just a tiny bit west of Yosemite Valley
|
| Posted: Mon Dec 29, 2014 7:40 pm Post subject: |
|
|
Might use this link to help identify part(s) you need....
http://www.piercemanifolds.com/category_s/250.htm
Mike has been in business for over 40 years, ill bet if its available he has it...
Dale
_________________
“Fear The Government That Wants To Take Your Guns"
"Kellison Sand Piper Roadster" For Street & Show.
"Joe Pody Sandrover" Buggy with 2180 for Autocross (Sold)
============================================================
All suggestions and advice are purely my own opinion. You are free to ignore them if you wish ... |
|
| Back to top |
|
|
mark tucker
Samba Member
Joined: April 08, 2009
Posts: 23950
Location: SHALIMAR ,FLORIDA
|
| Posted: Mon Dec 29, 2014 8:25 pm Post subject: |
|
|
| I bought from them a few times.and........well.... they have always been great. so i second the suggestion. |
|
| Back to top |
|
|
Cainepolo12
Samba Member
Joined: December 20, 2005
Posts: 27
Location: Nashville, TN
|
| Posted: Mon Dec 29, 2014 9:04 pm Post subject: |
|
|
| I have that diagram over my workbench with everything labeled and ready to go. It makes things so much easier for everyone when businesses actually care about building a positive reputation. |
|
| Back to top |
|
|
bluebus86
Banned
Joined: September 02, 2010
Posts: 11075
|
|
| Back to top |
|
|
|
